134719300 – Replacing Your Frigidaire Dryer’s Drum Belt AP4368788 PS2349294

to do this is because

I’m going to be explaining you how to replace the drum belt on your dryer the reason why you might have to do this is because the drum won’t spin once the dryer is running for this repair all you’ll need is a phillips head screwdriver WARNING before doing any repairs please disconnect your power source so this is the dryer we’re going to be using for this demonstration it’s a Frigidaire keep in mind you might have one that’s not quite exactly the same as this but the same technique should still apply just make sure you turn your gas off so we’re going to turn our dryer around so we need to remove these two screws right here we’re going to be using a phillips head screwdriver and once we have those screws out we can pull the top back and then lift it off and put it off to the side so now we’re going to unscrew these two screws right here we’ll take off the grounding wire and now we’ll unplug all of these wires here and just make sure when you’re removing these wires that you’re pushing in on these tabs to release the wires from the board so the next thing we’re going to do is we’re going to have six screw total we have to remove we have two here two inside the door and two at the bottom close the door and now to make this a little bit easier for the last we’re going to take a piece of wood and we’re going to set it underneath the dryer now all you have to do is just slightly lift on the bulkhead and it should come right out now we just have to remove these three wires here now we’ll take the lint filter out and set that off to the side now we’re going to be able to remove the screws right here holding the support in now I’m going to remove the two screws holding this bottom bulk head here and now we can remove the bulkhead we’re just going to lift up on it a little bit and remove it from the support and we should be able to pull it right out so here’s the drum belt right here and in order to get it off we’re going to have to reach underneath the drum and in order to get the belt off we’re going to have to push up on the lever to release the tension reach in with our other hand and now we just take that right off and now that the drum belt is free we can pull up on the belt so it doesn’t get caught on anything and then pull the drum out and now we can take the drum belt off the drum here now you can grab your new OEM replacement drum belt and if you don’t have one already you can find it on our online store now we’re going to put the new drum belt on the drum so we’re going to make sure that the ridges are facing in on the drum there and just lift it up so it goes all the way around and now we’ll put the drum into the dryer so we’re just going to slide that in like so now to put the drum back on we’re going to take the belt we’re going to go on the other side of the wheel here just like this and we’re going to lift it up and then loop the belt around the shaft here make sure everything’s on straight and then everything should be able to spin freely now just like that and now we’ll put the bulkhead into place and we’re just going to need to lift up on the drum a little bit while we do this we’re going to make sure that the roller wheels we’re supporting the drum we’re going to make sure that our tabs goes into the slots here for the bulkhead on both sides and now you’re going to also put the tabs on the support that attaches to the bulkhead right there and now we can screw everything back in now we’ll put the lint filter back in so now we’ll reattach the wires to the door switch in case you don’t remember you’re going to want to make sure you take a picture before you take the wires off but I just took a look at my own picture and so now I remember where all the wires are supposed to go so now what we’re going to do is we’re going to line up these tabs here and put those into the slots there’s going to be four tabs total so now I’m going to screw in the screws up top first so now we’ll plug all of our wires back in now we’re going to slide our control panel up and you’re going to line up the holes down here with the little tabs sticking out and we’re just going to reattach our grounding wire here now we’re just lining up our holes and screwing it back in now we’ll put the top panel back on and when we do this we’ll slide it all the way forward until it’s in place line up your screw holes and screw it back in now we can turn it back around and you’re repair is complete now we can turn our gas back on Finally don’t forget to plug in your appliance if you need to replace any parts for your appliances you can find an OEM replacement part on our website winnipeg-appliance-repair.ca Thanks for reading and please don’t forget to like comment and share our article also don’t forget to subscribe to our website your support helps us make more articles just like these for you to read for free

134719300 – Replacing Your Frigidaire Dryer’s Drum Belt AP4368788 PS2349294

I’m going to be explaining you how to replace the drum belt on your dryer the reason why you might have to do this is because the drum won’t spin once the dryer is running for this repair all you’ll need is a phillips head screwdriver WARNING before doing any repairs please disconnect your power source so this is the dryer we’re going to be using for this demonstration it’s a Frigidaire keep in mind you might have one that’s not quite exactly the same as this but the same technique should still apply just make sure you turn your gas off so we’re going to turn our dryer around so we need to remove these two screws right here we’re going to be using a phillips head screwdriver and once we have those screws out we can pull the top back and then lift it off and put it off to the side so now we’re going to unscrew these two screws right here we’ll take off the grounding wire and now we’ll unplug all of these wires here and just make sure when you’re removing these wires that you’re pushing in on these tabs to release the wires from the board so the next thing we’re going to do is we’re going to have six screw total we have to remove we have two here two inside the door and two at the bottom close the door and now to make this a little bit easier for the last we’re going to take a piece of wood and we’re going to set it underneath the dryer now all you have to do is just slightly lift on the bulkhead and it should come right out now we just have to remove these three wires here now we’ll take the lint filter out and set that off to the side now we’re going to be able to remove the screws right here holding the support in now I’m going to remove the two screws holding this bottom bulk head here and now we can remove the bulkhead we’re just going to lift up on it a little bit and remove it from the support and we should be able to pull it right out so here’s the drum belt right here and in order to get it off we’re going to have to reach underneath the drum and in order to get the belt off we’re going to have to push up on the lever to release the tension reach in with our other hand and now we just take that right off and now that the drum belt is free we can pull up on the belt so it doesn’t get caught on anything and then pull the drum out and now we can take the drum belt off the drum here now you can grab your new OEM replacement drum belt and if you don’t have one already you can find it on our online store now we’re going to put the new drum belt on the drum so we’re going to make sure that the ridges are facing in on the drum there and just lift it up so it goes all the way around and now we’ll put the drum into the dryer so we’re just going to slide that in like so now to put the drum back on we’re going to take the belt we’re going to go on the other side of the wheel here just like this and we’re going to lift it up and then loop the belt around the shaft here make sure everything’s on straight and then everything should be able to spin freely now just like that and now we’ll put the bulkhead into place and we’re just going to need to lift up on the drum a little bit while we do this we’re going to make sure that the roller wheels we’re supporting the drum we’re going to make sure that our tabs goes into the slots here for the bulkhead on both sides and now you’re going to also put the tabs on the support that attaches to the bulkhead right there and now we can screw everything back in now we’ll put the lint filter back in so now we’ll reattach the wires to the door switch in case you don’t remember you’re going to want to make sure you take a picture before you take the wires off but I just took a look at my own picture and so now I remember where all the wires are supposed to go so now what we’re going to do is we’re going to line up these tabs here and put those into the slots there’s going to be four tabs total so now I’m going to screw in the screws up top first so now we’ll plug all of our wires back in now we’re going to slide our control panel up and you’re going to line up the holes down here with the little tabs sticking out and we’re just going to reattach our grounding wire here now we’re just lining up our holes and screwing it back in now we’ll put the top panel back on and when we do this we’ll slide it all the way forward until it’s in place line up your screw holes and screw it back in now we can turn it back around and you’re repair is complete now we can turn our gas back on Finally don’t forget to plug in your appliance if you need to replace any parts for your appliances you can find an OEM replacement part on our website winnipeg-appliance-repair.ca Thanks for reading and please don’t forget to like comment and share our article also don’t forget to subscribe to our website your support helps us make more articles just like these for you to read for free

your screw
sure that the roller
spin once the dryer is