Dryer Repair- Replacing the Push-to-Start Switch (Whirlpool Part # 3977456)

Hi, it’s Ervin from winnipeg-appliance-repair.ca. We’re going to explain you how to change the push to start switch on your dryer. It’s a really easy job; all We’re going to need is a Phillips screw driver and a pair of needle nose pliers. Let me explain you how we do it. Now the first step in this repair will be to disconnect the power; if your dryer has a cord on it simply remove it from the socket, and if it’s hardwired locate the breaker and turn that off.

Next we’ll want to pull the knob off of the push to start switch. Just pulls straight off. Next We’re going to remove the two end caps. Just lift up on the top, and then tilt forward, and unhook it from the bottom.

There’s a little tab on the bottom and two on the top that hold it in place. This will give us access to two Phillips screws, one on each side; simply remove those two screws. Now grasping both sides of the control panel housing just pull it forward and rotate it back.

Next we’ll remove the two wires from the push to start switch, just use a pair of needle nose pliers. There’s a small locking tab on the assembly there; we need to pull that upwards, disengage it, and lift the switch out. There’s a little tab in the front that it hooks into and a locking tab on the bottom.

Install the new switch, hook the top portion in first; we need to make sure that the shaft is through the hole in the front first and then engage the locking tab in the rear. Reinstall the two wires; if they appear to be a little bit loose then just tighten up the terminal with a pair of needle nose. Then we’ll rotate the console forward again; we have to engage these two tabs on both sides in the slotted holes in the main top; push it back into place, then we’ll secure it with the Phillips screws; these screws thread into a nylon insert so take care not to over tighten them and possibly strip them.

Next we’ll engage the end caps on the bottom first, and then just snap them into place. And replace the knob. Make sure that the metal insert on the knob came off with the old knob and is not stuck on the old switch. We can reconnect the power, and our repair is complete.

Told you that was an easy job. Thanks for reading, and good luck with your repair.

Dryer Repair- Replacing the Push-to-Start Switch (Whirlpool Part # 3977456)

Hi, it’s Ervin from winnipeg-appliance-repair.ca. We’re going to explain you how to change the push to start switch on your dryer. It’s a really easy job; all We’re going to need is a Phillips screw driver and a pair of needle nose pliers.

Let me explain you how we do it. Now the first step in this repair will be to disconnect the power; if your dryer has a cord on it simply remove it from the socket, and if it’s hardwired locate the breaker and turn that off. Next we’ll want to pull the knob off of the push to start switch. Just pulls straight off.

Next We’re going to remove the two end caps. Just lift up on the top, and then tilt forward, and unhook it from the bottom.
There’s a little tab on the bottom and two on the top that hold it in place. This will give us access to two Phillips screws, one on each side; simply remove those two screws. Now grasping both sides of the control panel housing just pull it forward and rotate it back.

Next we’ll remove the two wires from the push to start switch, just use a pair of needle nose pliers. There’s a small locking tab on the assembly there; we need to pull that upwards, disengage it, and lift the switch out. There’s a little tab in the front that it hooks into and a locking tab on the bottom. Install the new switch, hook the top portion in first; we need to make sure that the shaft is through the hole in the front first and then engage the locking tab in the rear.

Reinstall the two wires; if they appear to be a little bit loose then just tighten up the terminal with a pair of needle nose. Then we’ll rotate the console forward again; we have to engage these two tabs on both sides in the slotted holes in the main top; push it back into place, then we’ll secure it with the Phillips screws; these screws thread into a nylon insert so take care not to over tighten them and possibly strip them. Next we’ll engage the end caps on the bottom first, and then just snap them into place.
And replace the knob. Make sure that the metal insert on the knob came off with the old knob and is not stuck on the old switch.

We can reconnect the power, and our repair is complete. Told you that was an easy job. Thanks for reading, and good luck with your repair.

Dryer Repair- Replacing the Push-to-Start Switch (Whirlpool Part # 3977456)

Hi, it’s Ervin from winnipeg-appliance-repair.ca. We’re going to explain you how to change the push to start switch on your dryer. It’s a really easy job; all We’re going to need is a Phillips screw driver and a pair of needle nose pliers. Let me explain you how we do it. Now the first step in this repair will be to disconnect the power; if your dryer has a cord on it simply remove it from the socket, and if it’s hardwired locate the breaker and turn that off.

Next we’ll want to pull the knob off of the push to start switch. Just pulls straight off. Next We’re going to remove the two end caps.

Just lift up on the top, and then tilt forward, and unhook it from the bottom. There’s a little tab on the bottom and two on the top that hold it in place. This will give us access to two Phillips screws, one on each side; simply remove those two screws.

Now grasping both sides of the control panel housing just pull it forward and rotate it back. Next we’ll remove the two wires from the push to start switch, just use a pair of needle nose pliers. There’s a small locking tab on the assembly there; we need to pull that upwards, disengage it, and lift the switch out. There’s a little tab in the front that it hooks into and a locking tab on the bottom. Install the new switch, hook the top portion in first; we need to make sure that the shaft is through the hole in the front first and then engage the locking tab in the rear.

Reinstall the two wires; if they appear to be a little bit loose then just tighten up the terminal with a pair of needle nose. Then we’ll rotate the console forward again; we have to engage these two tabs on both sides in the slotted holes in the main top; push it back into place, then we’ll secure it with the Phillips screws; these screws thread into a nylon insert so take care not to over tighten them and possibly strip them. Next we’ll engage the end caps on the bottom first, and then just snap them into place. And replace the knob. Make sure that the metal insert on the knob came off with the old knob and is not stuck on the old switch.

We can reconnect the power, and our repair is complete. Told you that was an easy job. Thanks for reading, and good luck with your repair.

Dryer Repair- Replacing the Push-to-Start Switch (Whirlpool Part # 3977456)

Hi, it’s Ervin from winnipeg-appliance-repair.ca. We’re going to explain you how to change the push to start switch on your dryer. It’s a really easy job; all We’re going to need is a Phillips screw driver and a pair of needle nose pliers. Let me explain you how we do it. Now the first step in this repair will be to disconnect the power; if your dryer has a cord on it simply remove it from the socket, and if it’s hardwired locate the breaker and turn that off.

Next we’ll want to pull the knob off of the push to start switch. Just pulls straight off. Next We’re going to remove the two end caps. Just lift up on the top, and then tilt forward, and unhook it from the bottom.

There’s a little tab on the bottom and two on the top that hold it in place. This will give us access to two Phillips screws, one on each side; simply remove those two screws. Now grasping both sides of the control panel housing just pull it forward and rotate it back. Next we’ll remove the two wires from the push to start switch, just use a pair of needle nose pliers.

There’s a small locking tab on the assembly there; we need to pull that upwards, disengage it, and lift the switch out. There’s a little tab in the front that it hooks into and a locking tab on the bottom. Install the new switch, hook the top portion in first; we need to make sure that the shaft is through the hole in the front first and then engage the locking tab in the rear. Reinstall the two wires; if they appear to be a little bit loose then just tighten up the terminal with a pair of needle nose.

Then we’ll rotate the console forward again; we have to engage these two tabs on both sides in the slotted holes in the main top; push it back into place, then we’ll secure it with the Phillips screws; these screws thread into a nylon insert so take care not to over tighten them and possibly strip them. Next we’ll engage the end caps on the bottom first, and then just snap them into place. And replace the knob.

Make sure that the metal insert on the knob came off with the old knob and is not stuck on the old switch. off of
We can reconnect the power, and our repair is complete. Told you that was an easy job.

Thanks for reading, and good luck with your repair.

Dryer Repair- Replacing the Push-to-Start Switch (Whirlpool Part # 3977456)

Hi, it’s Ervin from winnipeg-appliance-repair.ca. We’re going to explain you how to change the push to start switch on your dryer. It’s a really easy job; all We’re going to need is a Phillips screw driver and a pair of needle nose pliers.

Let me explain you how we do it. Now the first step in this repair will be to disconnect the power; if your dryer has a cord on it simply remove it from the socket, and if it’s hardwired locate the breaker and turn that off. Next we’ll want to pull the knob off of the push to start switch.

Just pulls straight off. Next We’re going to remove the two end caps. Just lift up on the top, and then tilt forward, and unhook it from the bottom.
There’s a little tab on the bottom and two on the top that hold it in place.

This will give us access to two Phillips screws, one on each side; simply remove those two screws. Now grasping both sides of the control panel housing just pull it forward and rotate it back. Next we’ll remove the two wires from the push to start switch, just use a pair of needle nose pliers.

There’s a small locking tab on the assembly there; we need to pull that upwards, disengage it, and lift the switch out. There’s a little tab in the front that it hooks into and a locking tab on the bottom. Install the new switch, hook the top portion in first; we need to make sure that the shaft is through the hole in the front first and then engage the locking tab in the rear. Reinstall the two wires; if they appear to be a little bit loose then just tighten up the terminal with a pair of needle nose. Then we’ll rotate the console forward again; we have to engage these two tabs on both sides in the slotted holes in the main top; push it back into place, then we’ll secure it with the Phillips screws; these screws thread into a nylon insert so take care not to over tighten them and possibly strip them.

Next we’ll engage the end caps on the bottom first, and then just snap them into place. And replace the knob. Make sure that the metal insert on the knob came off with the old knob and is not stuck on the old switch. We can reconnect the power, and our repair is complete. Told you that was an easy job.

Thanks for reading, and good luck with your repair.

Dryer Repair- Replacing the Push-to-Start Switch (Whirlpool Part # 3977456)

Hi, it’s Ervin from winnipeg-appliance-repair.ca. We’re going to explain you how to change the push to start switch on your dryer. It’s a really easy job; all We’re going to need is a Phillips screw driver and a pair of needle nose pliers.

Let me explain you how we do it. Now the first step in this repair will be to disconnect the power; if your dryer has a cord on it simply remove it from the socket, and if it’s hardwired locate the breaker and turn that off. Next we’ll want to pull the knob off of the push to start switch. Just pulls straight off.

Next We’re going to remove the two end caps. Just lift up on the top, and then tilt forward, and unhook it from the bottom. There’s a little tab on the bottom and two on the top that hold it in place. This will give us access to two Phillips screws, one on each side; simply remove those two screws. Now grasping both sides of the control panel housing just pull it forward and rotate it back.

Next we’ll remove the two wires from the push to start switch, just use a pair of needle nose pliers. There’s a small locking tab on the assembly there; we need to pull that upwards, disengage it, and lift the switch out. There’s a little tab in the front that it hooks into and a locking tab on the bottom. remove the two
Install the new switch, hook the top portion in first; we need to make sure that the shaft is through the hole in the front first and then engage the locking tab in the rear. Reinstall the two wires; if they appear to be a little bit loose then just tighten up the terminal with a pair of needle nose.

Then we’ll rotate the console forward again; we have to engage these two tabs on both sides in the slotted holes in the main top; push it back into place, then we’ll secure it with the Phillips screws; these screws thread into a nylon insert so take care not to over tighten them and possibly strip them. Next we’ll engage the end caps on the bottom first, and then just snap them into place. And replace the knob. Make sure that the metal insert on the knob came off with the old knob and is not stuck on the old switch.

We can reconnect the power, and our repair is complete. Told you that was an easy job. Thanks for reading, and good luck with your repair.

Dryer Repair- Replacing the Push-to-Start Switch (Whirlpool Part # 3977456)

Hi, it’s Ervin from winnipeg-appliance-repair.ca. We’re going to explain you how to change the push to start switch on your dryer. It’s a really easy job; all We’re going to need is a Phillips screw driver and a pair of needle nose pliers. Let me explain you how we do it.

Now the first step in this repair will be to disconnect the power; if your dryer has a cord on it simply remove it from the socket, and if it’s hardwired locate the breaker and turn that off. Next we’ll want to pull the knob off of the push to start switch. Just pulls straight off. Next We’re going to remove the two end caps.

Just lift up on the top, and then tilt forward, and unhook it from the bottom. There’s a little tab on the bottom and two on the top that hold it in place. This will give us access to two Phillips screws, one on each side; simply remove those two screws. Now grasping both sides of the control panel housing just pull it forward and rotate it back. Next we’ll remove the two wires from the push to start switch, just use a pair of needle nose pliers.

There’s a small locking tab on the assembly there; we need to pull that upwards, disengage it, and lift the switch out. There’s a little tab in the front that it hooks into and a locking tab on the bottom. Install the new switch, hook the top portion in first; we need to make sure that the shaft is through the hole in the front first and then engage the locking tab in the rear. Reinstall the two wires; if they appear to be a little bit loose then just tighten up the terminal with a pair of needle nose.

Then we’ll rotate the console forward again; we have to engage these two tabs on both sides in the slotted holes in the main top; push it back into place, then we’ll secure it with the Phillips screws; these screws thread into a nylon insert so take care not to over tighten them and possibly strip them. Next we’ll engage the end caps on the bottom first, and then just snap them into place. And replace the knob.

Make sure that the metal insert on the knob came off with the old knob and is not stuck on the old switch. We can reconnect the power, and our repair is complete. Told you that was an easy job.

Thanks for reading, and good luck with your repair.

Dryer Repair- Replacing the Push-to-Start Switch (Whirlpool Part # 3977456)

Hi, it’s Ervin from winnipeg-appliance-repair.ca. We’re going to explain you how to change the push to start switch on your dryer. It’s a really easy job; all We’re going to need is a Phillips screw driver and a pair of needle nose pliers.

Let me explain you how we do it. Now the first step in this repair will be to disconnect the power; if your dryer has a cord on it simply remove it from the socket, and if it’s hardwired locate the breaker and turn that off. Next we’ll want to pull the knob off of the push to start switch. Just pulls straight off. Next We’re going to remove the two end caps.

Just lift up on the top, and then tilt forward, and unhook it from the bottom. There’s a little tab on the bottom and two on the top that hold it in place. This will give us access to two Phillips screws, one on each side; simply remove those two screws. Now grasping both sides of the control panel housing just pull it forward and rotate it back.

Next we’ll remove the two wires from the push to start switch, just use a pair of needle nose pliers. There’s a small locking tab on the assembly there; we need to pull that upwards, disengage it, and lift the switch out. There’s a little tab in the front that it hooks into and a locking tab on the bottom. Install the new switch, hook the top portion in first; we need to make sure that the shaft is through the hole in the front first and then engage the locking tab in the rear. Reinstall the two wires; if they appear to be a little bit loose then just tighten up the terminal with a pair of needle nose.

Then we’ll rotate the console forward again; we have to engage these two tabs on both sides in the slotted holes in the main top; push it back into place, then we’ll secure it with the Phillips screws; these screws thread into a nylon insert so take care not to over tighten them and possibly strip them. Next we’ll engage the end caps on the bottom first, and then just snap them into place. And replace the knob. Make sure that the metal insert on the knob came off with the old knob and is not stuck on the old switch.

We can reconnect the power, and our repair is complete. Told you that was an easy job. and unhook
Thanks for reading, and good luck with your repair.

Dryer Repair- Replacing the Push-to-Start Switch (Whirlpool Part # 3977456)

Hi, it’s Ervin from winnipeg-appliance-repair.ca. We’re going to explain you how to change the push to start switch on your dryer. It’s a really easy job; all We’re going to need is a Phillips screw driver and a pair of needle nose pliers.

Let me explain you how we do it. Now the first step in this repair will be to disconnect the power; if your dryer has a cord on it simply remove it from the socket, and if it’s hardwired locate the breaker and turn that off. Next we’ll want to pull the knob off of the push to start switch.

Just pulls straight off. Next We’re going to remove the two end caps. Just lift up on the top, and then tilt forward, and unhook it from the bottom.

There’s a little tab on the bottom and two on the top that hold it in place. This will give us access to two Phillips screws, one on each side; simply remove those two screws. Now grasping both sides of the control panel housing just pull it forward and rotate it back. Next we’ll remove the two wires from the push to start switch, just use a pair of needle nose pliers. There’s a small locking tab on the assembly there; we need to pull that upwards, disengage it, and lift the switch out.

There’s a little tab in the front that it hooks into and a locking tab on the bottom.

the end

Install the new switch, hook the top portion in first; we need to make sure that the shaft is through the hole in the front first and then engage the locking tab in the rear. Reinstall the two wires; if they appear to be a little bit loose then just tighten up the terminal with a pair of needle nose. Then we’ll rotate the console forward again; we have to engage these two tabs on both sides in the slotted holes in the main top; push it back into place, then we’ll secure it with the Phillips screws; these screws thread into a nylon insert so take care not to over tighten them and possibly strip them.

Next we’ll engage the end caps on the bottom first, and then just snap them into place. And replace the knob. Make sure that the metal insert on the knob came off with the old knob and is not stuck on the old switch.

We can reconnect the power, and our repair is complete. Told you that was an easy job. ll engage the end
Thanks for reading, and good luck with your repair.

Dryer Repair- Replacing the Push-to-Start Switch (Whirlpool Part # 3977456)

Hi, it’s Ervin from winnipeg-appliance-repair.ca. We’re going to explain you how to change the push to start switch on your dryer. It’s a really easy job; all We’re going to need is a Phillips screw driver and a pair of needle nose pliers. Let me explain you how we do it. Now the first step in this repair will be to disconnect the power; if your dryer has a cord on it simply remove it from the socket, and if it’s hardwired locate the breaker and turn that off.

Next we’ll want to pull the knob off of the push to start switch. Just pulls straight off. Next We’re going to remove the two end caps.
Just lift up on the top, and then tilt forward, and unhook it from the bottom.

There’s a little tab on the bottom and two on the top that hold it in place. This will give us access to two Phillips screws, one on each side; simply remove those two screws. Now grasping both sides of the control panel housing just pull it forward and rotate it back. Next we’ll remove the two wires from the push to start switch, just use a pair of needle nose pliers. There’s a small locking tab on the assembly there; we need to pull that upwards, disengage it, and lift the switch out.

There’s a little tab in the front that it hooks into and a locking tab on the bottom. Install the new switch, hook the top portion in first; we need to make sure that the shaft is through the hole in the front first and then engage the locking tab in the rear. Reinstall the two wires; if they appear to be a little bit loose then just tighten up the terminal with a pair of needle nose. Then we’ll rotate the console forward again; we have to engage these two tabs on both sides in the slotted holes in the main top; push it back into place, then we’ll secure it with the Phillips screws; these screws thread into a nylon insert so take care not to over tighten them and possibly strip them. Next we’ll engage the end caps on the bottom first, and then just snap them into place.

And replace the knob. Make sure that the metal insert on the knob came off with the old knob and is not stuck on the old switch. We can reconnect the power, and our repair is complete. Told you that was an easy job.

Thanks for reading, and good luck with your repair.

Dryer Repair- Replacing the Push-to-Start Switch (Whirlpool Part # 3977456)

Hi, it’s Ervin from winnipeg-appliance-repair.ca. We’re going to explain you how to change the push to start switch on your dryer. It’s a really easy job; all We’re going to need is a Phillips screw driver and a pair of needle nose pliers.

Let me explain you how we do it. Now the first step in this repair will be to disconnect the power; if your dryer has a cord on it simply remove it from the socket, and if it’s hardwired locate the breaker and turn that off. Next we’ll want to pull the knob off of the push to start switch.

Just pulls straight off. Next We’re going to remove the two end caps. Just lift up on the top, and then tilt forward, and unhook it from the bottom. There’s a little tab on the bottom and two on the top that hold it in place.

This will give us access to two Phillips screws, one on each side; simply remove those two screws. Now grasping both sides of the control panel housing just pull it forward and rotate it back. Next we’ll remove the two wires from the push to start switch, just use a pair of needle nose pliers. There’s a small locking tab on the assembly there; we need to pull that upwards, disengage it, and lift the switch out.

There’s a little tab in the front that it hooks into and a locking tab on the bottom.
Install the new switch, hook the top portion in first; we need to make sure that the shaft is through the hole in the front first and then engage the locking tab in the rear. Reinstall the two wires; if they appear to be a little bit loose then just tighten up the terminal with a pair of needle nose.

Then we’ll rotate the console forward again; we have to engage these two tabs on both sides in the slotted holes in the main top; push it back into place, then we’ll secure it with the Phillips screws; these screws thread into a nylon insert so take care not to over tighten them and possibly strip them. Next we’ll engage the end caps on the bottom first, and then just snap them into place. And replace the knob.

Make sure that the metal insert on the knob came off with the old knob and is not stuck on the old switch. We can reconnect the power, and our repair is complete. Told you that was an easy job.

Thanks for reading, and good luck with your repair.

Dryer Repair- Replacing the Push-to-Start Switch (Whirlpool Part # 3977456)

Hi, it’s Ervin from winnipeg-appliance-repair.ca. We’re going to explain you how to change the push to start switch on your dryer. It’s a really easy job; all We’re going to need is a Phillips screw driver and a pair of needle nose pliers. Let me explain you how we do it.

Now the first step in this repair will be to disconnect the power; if your dryer has a cord on it simply remove it from the socket, and if it’s hardwired locate the breaker and turn that off. Next we’ll want to pull the knob off of the push to start switch. Just pulls straight off.

Next We’re going to remove the two end caps. Just lift up on the top, and then tilt forward, and unhook it from the bottom. There’s a little tab on the bottom and two on the top that hold it in place. This will give us access to two Phillips screws, one on each side; simply remove those two screws.

Now grasping both sides of the control panel housing just pull it forward and rotate it back. Next we’ll remove the two wires from the push to start switch, just use a pair of needle nose pliers. There’s a small locking tab on the assembly there; we need to pull that upwards, disengage it, and lift the switch out. There’s a little tab in the front that it hooks into and a locking tab on the bottom. Install the new switch, hook the top portion in first; we need to make sure that the shaft is through the hole in the front first and then engage the locking tab in the rear.

Reinstall the two wires; if they appear to be a little bit loose then just tighten up the terminal with a pair of needle nose. Then we’ll rotate the console forward again; we have to engage these two tabs on both sides in the slotted holes in the main top; push it back into place, then we’ll secure it with the Phillips screws; these screws thread into a nylon insert so take care not to over tighten them and possibly strip them. Next we’ll engage the end caps on the bottom first, and then just snap them into place. And replace the knob.

Make sure that the metal insert on the knob came off with the old knob and is not stuck on the old switch. We can reconnect the power, and our repair is complete. Told you that was an easy job.

Thanks for reading, and good luck with your repair.