Duet/HE3 Electric Dryer Drum Seal Replacement #280114

disconnect the wire

winnipeg-appliance-repair.ca encourages you to perform this procedure safely In this article we will explain one or more of these icons to alert you when to use caution as with any repair be sure you’ve unplugged the appliance before beginning your first step is to remove the top panel screws and set the panel aside next depress the tabs on the control panel and pull it off disconnect the wire harness remove the screws to release the circuit board bracket remove the control bracket screws and pull the bracket off now remove the screws located at the base of the dryer pull the lower panel out and then down to detach reach into the lower cabinet to disconnect the door switch and moisture sensor wire harnesses remove the screws at the bottom and at the top of the front panel remove the mounting screws located inside the door and pull the panel off remove the lower bulkhead mounting screws and loosen the upper screws remove the mounting screws from the blower housing lift the bulkhead off the upper mounting screws and set it aside next remove the dryer belt by depressing the pulley to release the tension and unthreading the belt from the pulley and motor shaft now use the bell to lift up the drum if it’s still intact remove the old seal and clean up excess residue prepare the new felt seal for installation by first applying the high temperature adhesive to the drum rim then align the new seal around the rim applying pressure as you go allow twenty minutes for the adhesive to dry replace the drum by aligning it’s rim on the two rear rollers and loop the belt around the tension pulley and motor shaft in a zig-zag formation rotate the drum to help aligned the belt now reinstall the bulkhead by aligning it on the upper screws tighten the screws replace the lower screws as well as the ones for the blower housing reattach the front panel by lining it up on the cabinet then secure it with the upper and lower screws as well as the screws inside the door reconnect the door switch and moisture sensor wire harnesses slide the lower panel up into position and secure it with the screws reinstall the control panel bracket reattach the circuit board bracket reconnect the control panel’s wire harness and snap the panel back into place replace the top panel secure it with the screws and plug the appliance back in to make sure it’s functioning properly

Duet/HE3 Electric Dryer Drum Seal Replacement #280114

winnipeg-appliance-repair.ca encourages you to perform this procedure safely In this article we will explain one or more of these icons to alert you when to use caution as with any repair be sure you’ve unplugged the appliance before beginning your first step is to remove the top panel screws and set the panel aside next depress the tabs on the control panel and pull it off disconnect the wire harness remove the screws to release the circuit board bracket remove the control bracket screws and pull the bracket off now remove the screws located at the base of the dryer pull the lower panel out and then down to detach reach into the lower cabinet to disconnect the door switch and moisture sensor wire harnesses remove the screws at the bottom and at the top of the front panel remove the mounting screws located inside the door and pull the panel off remove the lower bulkhead mounting screws and loosen the upper screws remove the mounting screws from the blower housing lift the bulkhead off the upper mounting screws and set it aside next remove the dryer belt by depressing the pulley to release the tension and unthreading the belt from the pulley and motor shaft now use the bell to lift up the drum if it’s still intact remove the old seal and clean up excess residue prepare the new felt seal for installation by first applying the high temperature adhesive to the drum rim then align the new seal around the rim applying pressure as you go allow twenty minutes for the adhesive to dry replace the drum by aligning it’s rim on the two rear rollers and loop the belt around the tension pulley and motor shaft in a zig-zag formation rotate the drum to help aligned the belt now reinstall the bulkhead by aligning it on the upper screws tighten the screws replace the lower screws as well as the ones for the blower housing reattach the front panel by lining it up on the cabinet then secure it with the upper and lower screws as well as the screws inside the door reconnect the door switch and moisture sensor wire harnesses slide the lower panel up into position and secure it with the screws reinstall the control panel bracket reattach the circuit board bracket reconnect the control panel’s wire harness and snap the panel back into place replace the top panel secure it with the screws and plug the appliance back in to make sure it’s functioning properly

and moisture

next remove the dryer belt

to detach reach into the